A LOOK AT THE KEYPAD
A quick look at the keys should help you understand the scanner’s
functions.
SCAN – scans through the programmed channels.
MANUAL – stops scanning and lets you directly enter a channel
number.
LOCKOUT/DLY – locks out a selected channel or programs a two-second
delay for the selected channel.
PRIORITY – sets the priority channel and turns it on and off.
CLEAR/. – clears an incorrect entry or enters the decimal point
when programming frequencies.
MON/91-100/0 – accesses the 10 monitor memories.
WX/E (enter) – scans through the preprogrammed weather channels or
enters frequencies into channels.
KEYLOCK/ – a quick press turns on the display’s backlight for 15
(light symbol) seconds, and when held down, it locks/unlocks the
keypad to prevent accidental entries.
PROGRAM – programs frequencies into channels.
LIMIT, (\/), – searches for active frequencies so you can find ones
and (/\) you want to store.
Number Keys – each key has a single digit on it and a range of
numbers printed above it. The single digits refer to
the number of a channel or frequency. The range of
numbers (21-30, for example) shows the channels that
make up a memory bank. In addition, the keypad has
different functions in the manual, scan, and program
modes.
A LOOK AT THE DISPLAY
A quick look at the display should help you understand what the scanner
can do.
MON – appears with a number (1-10) to show which monitor memory you
are listening to.
BANK – shows which channel-storage banks are turned on.
KEYLOCK – appears when you lock the keypad.
BATT. Lo – appears when the battery is low.
CH – appears with a digit that shows which of the 100 channels the
scanner is tuned to.
P – appears when you listen to the priority channel.
MHz – appears with digits that show which frequency the scanner is
turned to.
SCAN – appears when you scan channels.
MAN – appears when you manually select a channel.
PGM – appears while you program frequencies into the scanner’s
channels.
PRI – appears when the priority feature is selected.
L/O – appears when you manually select a locked channel.
DLY – appears when you program a 2-second delay for a channel.
WX – appears when you scan the preprogrammed weather channels.
(\/) and – indicates the search direction.
(/\)
SRCH – appears during a limit search and a direct search.
-L- – appears instead of the channel number during a limit search.
-d- – appears instead of the channel number during a direct search.
Hi – appears with a frequency to show the upper limit of the
frequency range to search.
Lo – appears with a frequency to show the lower limit of the
frequency range to search.
UNDERSTANDING CHANNEL-STORAGE BANKS AND MONITOR MEMORIES
Your scanner can store up to 110 frequencies. You store each frequency in
either a permanent memory location, called a channel, or a temporary
memory location, called a monitor memory. This scanner has 100 channels
and 10 monitor memories.
Channel-Storage Banks
To make it easier to identify and select the channels you listen to most
often, channels are divided into 10 channel-storage banks of 10 channels
each. Use each channel-storage bank to group frequencies, such as those
used by the police department, fire department, ambulance or aircraft
services (see “Guide to the Action Bands” in Faxback Doc. # 17653).
For example, the police might use four frequencies, one for each side of
town. You could program the four police frequencies starting with Channel
1 (the first channel in Bank 1), and then program the fire department
frequencies starting with Channel 11 (the first channel in Bank 2).
Monitor Memories
The scanner also has 10 temporary memories called monitor memories. Use
these memories to temporarily store frequencies while you decide whether
or not to save them into channels. This is handy for quickly storing an
active frequency when you are searching through an entire band.
Note: To store frequencies into a monitor memory, you must first perform
a limit search or direct search. See “Searching For and
Temporarily Storing Active Frequencies” in Faxback Doc. # 47808.
(BR/eb 5/21/98)